18 @0
            OPTi PCI IDE - OPTi PCI IDE Controller

OPTi PCI IDE is a bus-mastering IDE controller capable of operating 
at PCI local  bus  frequencies  25MHz or  33MHz. It can support PIO
modes 0-4, DMA modes 0-2.

Additional features include: Dual channel support i.e. upto  4  IDE 
devices can be connected.

Drivers for accessing devices  with hardware  optimization  for DOS
and Windows operating systems are included.

 




                       Press <Esc> when you have read this message.
18 @1
            EZIDE  - OPTi IDE  Software Installation

By now, EZIDE has already scanned  for all IDE devices installed in
your  system. The "Connected IDE Hardware/Device(s)"  window  shows
you all IDE devices  that  EZIDE  has detected in  the system. If a 
particular device is  not listed here, it is most  likely that  the
connection or power to that device is not proper.

To install OPTi IDE software on your fixed  disk, select the option
"Install DOS/Windows/Netware Drivers" and press <Enter>.

To  know  more  about  the IDE  devices in your  system, select the
option "View IDE Hardware Info" and press <Enter>.

To learn  about t he OPTi IDE software  components  and their usage,
select the option "View IDE Software Info" and press <Enter>.

                       Press <Esc> when you have read this message.
18 @2
            View  IDE  Hardware  Information

The "Connected IDE Hardware/Device(s)" window shows you all devices
connected to your system.To obtain more information on a particular
IDE device, use the cursor  movement keys to  highlight that device
and press <Enter> key.

If you  have installed  a OPTi PCI IDE controller, but  it does not
appear  in  the  list, please  check that the SYS file  is  in  the
directory  from where you invoked the EZIDE. 

Also ensure that hardware jumpers etc. do  not clash with any other
component in the system.




                       Press <Esc> when you have read this message.
11 @3



The  software  utilities/drivers  shipped  with
OPTi EZIDE are listed to the right.

To  learn about a OPTi IDE  software component,
highlight the file and press <Enter>
    
To return to installation options, press <Esc>

18 @4
            View  IDE  Software  Information

OPTi  EZIDE  comes  with  drivers  for  DOS and Windows.

The files  have been listed in a window to the right of the screen.
Use  cursor  movement  keys to reach a  file name and press <Enter>
to select  that  file. The  selected  software  component   will be
described.

When  you execute the option  "Install DOS/Windows/Netware Drivers"
most of these files, will be copied in C:\OPTIIDE (or as specified)
directory.





                       Press <Esc> when you have read this message.
18 @5    
                           NOTICE


EZIDE  has  modified  your  CONFIG.SYS  file.

If you had  a  CONFIG.SYS file, prior to running the EZIDE,  it has
been  saved  as CONFIG.OLD.

The driver will be loaded during the next system reboot.








		 Press <Esc> To Return To The Main Menu.
18 @6    
                           NOTICE


EZIDE has created CONFIG.SYS file in C:\.


  
  
  
  
  
  
  
  
  
  
  
                                   Press <Esc> to return to MS-DOS.
18 @7    
                           PROBLEM


EZIDE could not create or modify CONFIG.SYS file.

Either this files have been protected by you against  modification,
or  there is   no  space  on  the hard disk. Go  back to MS-DOS and
take  corrective  action. Then  you can run EZIDE again to complete
the IDE software installation.








                                   Press <Esc> to return to MS-DOS.
18 @8    
                           PROBLEM


EZIDE  could not find the fixed disk  C:  where  IDE  software  can
be  installed. You  must create a MS-DOS partition on a fixed disk.

To initialize any IDE hard disk, press <Enter>.

To view IDE hardware or software information, press <Esc>.









18 @9    
                           PROBLEM


EZIDE could not find OPTi PCI IDE controller in your system.

For proper installation please verify :
1. The  devices  are powered on  and  connected properly to the IDE
   connectors onboard.

2. Check  that  two  devices  connected via the same cable have the
   correct master/slave jumper settings.






                    To return to installation options, press <Esc>.
18 @10   
                           PROBLEM


EZIDE could not find any IDE device connected in your system.

For proper installation please verify :
1. The devices are powered on and  connected  properly  to  the IDE
   connectors onboard.

2. Check  that  two  devices connected via the  same cable have the
   correct master/slave jumper settings.




  
 
                    To return to installation options, press <Esc>.
18 @11    
            Installation of DOS and Windows Drivers

To  install OPTi  drivers, you must have a fixed disk drive C:. The
OPTi IDE  software files  will  be installed  in  the  fixed  disk.
You can  initialize  your  hard disks using normal DOS services and
utilities e.g. MS-DOS FDISK and FORMAT to create the fixed disk DOS
partition.

You will  have a choice to install the IDE drivers in C:\OPTIIDE or
any other directory. The CONFIG.SYS file will be modified by EZIDE.

EZIDE  will  automatically install the necessary drivers, depending
on your request and IDE devices detected in the system.




                       Press <Esc> when you have read this message.
18 @12    
                           NOTICE


EZIDE  has  modified  the SYSTEM.INI file.

Original SYSTEM.INI file has been saved as SYSTEM.OLD.











                       Press <Esc> when you have read this message.
18 @13    
                           PROBLEM


EZIDE can not find [386Enh] section in the SYSTEM.INI File.













                       Press <Esc> when you have read this message.
18 @14    
                           PROBLEM


EZIDE can not find SYSTEM.INI file in the specified directory.













                       Press <Esc> when you have read this message.
18 @15    
                           PROBLEM


EZIDE can not backup SYSTEM.INI file.

SYSTEM.INI will not be modified.











                       Press <Esc> when you have read this message.
18 @30
            EZIDE - OPTi IDE  Software Installation

OPTi  EZIDE simplifies the  installation  of IDE software after you
have connected your IDE peripherals to a system with a OPTi PCI IDE 
controller.

This  program  allows  you to  view all the IDE peripherals in your
system, describes  the  OPTi IDE  software  components and installs
them on your fixed disk.

The  EZIDE.EXE  and its  overlay files are copied in the C:\OPTIIDE
(or as specified) directory, so that you will not require the EZIDE 
diskette when you add IDE peripherals. 

You can execute the program  from your fixed disk as well.


                       Press <Esc> when you have read this message.
18 @31
            VICDRV.SYS - DOS Driver for OPTi PCI IDE

VICDRV.SYS is the DOS driver  for  the  OPTi PCI  Bus mastering IDE
controller from OPTi Inc.. This driver is to be installed by adding
the following line in the CONFIG.SYS file:

        DEVICE=<pathname>VICDRV.SYS

You can use 2 command line options: 
/P : in this case  the driver  will operate in PIO mode, by default
     it operates in bus mastering mode.
/Mdrvno=modeval: where  drvno is  the  drive  number (0, 1, 2 or 3)
     and  modeval  indicates the mode value(0-4) of drive selected.
     This option is used to override the default mode timing of the 
     drive(which  is the highest mode supported by it).


                       Press <Esc> when you have read this message.
18 @32
            OPTIVIC.386 - Windows Driver for OPTi PCI IDE

OPTIVIC.386 is the  Windows  driver for the  OPTi PCI Bus mastering
IDE controller  from OPTi Inc.. This  driver is  to be installed by
adding  the  following  lines in the [386Enh] section of SYSTEM.INI
file:

        32BitDiskAccess=ON
        device=<pathname>\opti13.386
        device=<pathname>\optivic.386

Remove  lines "device=*wdctrl" and  "device=*int13" from SYSTEM.INI
file, if they exist.




                       Press <Esc> when you have read this message.
18 @33
            OPTI13.386 - Int 13h API Translation VxD.
















                       Press <Esc> when you have read this message.
18 @34
                          FILEDATA.EZI


This is an overlay file used by the EZIDE program.



     
     
     
     
     
     
     
     
     
     
                       Press <Esc> when you have read this message.
18 @35
                          MESSAGES.EZI


This is an overlay file used by the EZIDE program.













                       Press <Esc> when you have read this message.
